This gearmotor is a miniature medium-power, 6 V brushed DC motor with a 51.45:1 metal gearbox. It has a cross section of 10 × 12 mm, and the D-shaped gearbox output shaft is 9 mm long and 3 mm in diameter.


Key specifications:

voltage: 6 V

no-load performance: 420 RPM, 40 mA

stall extrapolation: 0.54 kg⋅cm (7.5 oz⋅in), 0.67 A



Overview


These tiny brushed DC gearmotors are available in a wide range of gear ratios—from 5:1 up to 1000:1—and with five different motors: high-power 6 V and 12 V motors with long-life carbon brushes (HPCB), and high-power (HP), medium power (MP), and low power (LP) 6 V motors with shorter-life precious metal brushes. The 6 V and 12 V HPCB motors offer the same performance at their respective nominal voltages, just with the 12 V motor drawing half the current of the 6 V motor. The 6 V HPCB and 6 V HP motors are identical except for their brushes, which only affect the lifetime of the motor.


The HPCB versions (shown on the left in the picture below) can be differentiated from versions with precious metal brushes (shown on the right) by their copper-colored terminals. Note that the HPCB terminals are 0.5 mm wider than those on the other micro metal gearmotor versions (2 mm vs. 1.5 mm), and they are about 1 mm closer together (6 mm vs. 7 mm).





Versions of these gearmotors are also available with an additional 1 mm-diameter output shaft that protrudes from the rear of the motor. This 4.5 mm-long rear shaft rotates at the same speed as the input to the gearbox and offers a way to add an encoder, such as our magnetic encoder for micro metal gearmotors

With the exception of the 1000:1 gear ratio versions, all of the micro metal gearmotors have the same physical dimensions, so one version can be easily swapped for another if your design requirements change.


In general, these kinds of motors can run at voltages above and below their nominal voltages; lower voltages might not be practical, and higher voltages could start negatively affecting the life of the motor.


Details for item #2365


Exact gear ratio: 32×33×35×3815×14×13×1051.45:1


Gearmotor Dimensions


In terms of size, these gearmotors are very similar to Sanyo’s popular 12 mm NA4S DC gearmotors, and gearmotors with this form factor are occasionally referred to as N20 motors. The versions with carbon brushes (HPCB) have slightly different terminal and end-cap dimensions than the versions with precious metal brushes, but all of the other dimensions are identical.


Dimensions of versions with carbon brushes (HPCB)


Dimensions of the Pololu micro metal gearmotors with carbon brushes (HPCB). Units are mm over [inches].


Dimensions of versions with precious metal brushes (LP, MP, and HP)


Dimensions of the Pololu micro metal gearmotors with precious metal brushes: low-power (LP), medium-power (MP), and high-power (HP). Units are mm over [inches].




Dimensions


Size: 10 × 12 × 26 mm1
Weight: 9.5 g
Shaft diameter: 3 mm2


General specifications


Gear ratio: 51.45:1
No-load speed @ 6V: 420 rpm
No-load current @ 6V: 0.04 A
Stall current @ 6V: 0.67 A
Stall torque @ 6V: 0.54 kg·cm
Max output power @ 6V: 0.55 W
Extended motor shaft?: N
Motor type: 0.67A stall @ 6V (MP 6V)


Performance at maximum efficiency


Max efficiency @ 6V: 33 %
Speed at max efficiency: 310 rpm
Torque at max efficiency: 0.12 kg·cm
Current at max efficiency: 0.19 A
Output power at max efficiency: 0.38 W


Notes:


1. Output shaft adds 9 mm to the 26 mm length.
2. D shaft.


Micro-metal-gearmotors- Datasheet.pdf





2365 - 50:1 Micro Metal Gearmotor MP 6V

  • Brand: Pololu
  • Product Code: ES001284
  • Availability: In Stock
  • 15.95€